USER’S MANUAL. GA-8IGMK. P4 Titan Series Motherboard. Pentium® 4 Processor Motherboard. Rev. 12ME-8IG1KMK View and Download Gigabyte GA-8IGMK user manual online. P4 Titan Series Motherboard. GA-8IGMK Motherboard pdf manual download. Manuals and User Guides for Gigabyte GA-8IGMK. We have 2 Gigabyte GA- 8IGMK manuals available for free PDF download: User Manual.

Author: Zulkishakar Domi
Country: Vietnam
Language: English (Spanish)
Genre: Art
Published (Last): 13 May 2005
Pages: 71
PDF File Size: 9.91 Mb
ePub File Size: 7.94 Mb
ISBN: 395-8-68993-810-6
Downloads: 58090
Price: Free* [*Free Regsitration Required]
Uploader: Faekus

The author assumes no responsibility for any errors or omissions that may appear in this document nor manuao the author make a commitment to update the information contained herein.

Gigabyte GA-8IGMK user manuals download

Third-party brands and names are the property of their respective owners. Please do not remove any labels on motherboard, this may void the warranty of this motherboard. This device complies with part 15 of the FCC Rules. Table of Content Warning PCB surface, because the circuit wire may be near by the hole. Be careful, don’t let the screw contact any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the board or cause board malfunctioning.

CPU, chipset and most of the peripherals. Chapter 2 Hardware Installation Process To set up your computer, you must complete the following steps: Pin1 indicator Pin1 indicator 4.

Locate Pin 1 in the socket and 3. Then insert the CPU into the socket. Please use Intel approved cooling fan. We recommend you to apply the thermal tape to provide better heat conduction between your CPU and cooling fan. Then push it down. Reverse the installation steps when you wish to remove the DIMM module.

When Dual Channel Technology is activated, the bandwidth of memory bus will be double the original one,with the fastest speed at 6. When an AGP 2X 3. Informing users that system might not boot up normally due to AGP 2X 3. Connect ribbon cables, cabinet wires and power supply Step AC power cord should only be connected to your power supply unit after ATX power cable and other related devices are firmly connected to the mainboard.

The CPU fan connector supports Max. The red stripe of the ribbon cable must be the same side with the Pin1. Normal Operation Green Close: Normal Operation Red Close: It will blink when the system enters suspend mode. Please note, you can have the alternative of using front audio connector or of using rear audio connector to play sound.


Be careful with the polarity of the front USB connector. Check the pin assignment while you connect the front USB cable.

Please contact your nearest dealer for optional front USB cable. Make sure the pin 1 on the IR device is aling with pin one the connector. For detail information please contact your autherized Gigabyte distributor.

On the contrary when Jumper is manuql to “close”, the current status remains. The program that allows users to modify the basic system configuration. Integrated Peripherals This setup page includes all onboard peripherals. Power Management Setup This setup page includes all the items of Green function features.

GA-8IGMK (rev. 1.x) | Placas-mãe – GIGABYTE Brazil

The time manuaal calculated base on the hour military-time clock. For example, 1 p. Enabled Enable USB 2. Disabled Disable onboard LPT port. Parallel Port Mode This feature allows you to connect with an advanced printer via the port mode it supports.

Using Parallel port as Standard Parallel Port. Using Parallel port as Extended Capabilities Port. In standby mode S1power LED will blink. Off by Power button Instant-off Press power button then Power off instantly. Default value Delay 4 Sec. Press power button 4 sec. Enter suspend if button is pressed less than 4 sec.

When AC-power back to the system, the system will be in “Off” state.

Gigabyte GA-8IG1000MK user manuals

Optimized Defaults Figure 6: If system hangs up before enter CMOS setup utility, wait for 20 sec for times out reboot. When time out occur, system will reset and run at CPU default Host clock at next boot. Incorrect using it may cause your system broken. For power End-User use only! Type “N” will return to Setup Utility. This wonderful software is now free bundled in Gigabyte motherboard attached in driver CD.

Users may make a test drive of “EasyTune 4” to find out more amazing features by themselves. What is Q-Flash Utility?

Q-Flash utility is a pre-O. How to use Q-Flash? Press Enter to Run. Please press any key to continue You have completed the flashed and now can restart system. Click ” BIOS” item. Please follow next step to install the function! Stereo Speakers Connection and Settings: We recommend that you use the speaker with amplifier to acqiire the best sound effect if the stereo output is applied.

When the “Environment settings” is “None”, the sound would be performed as stereo mode 2 chan- nels output. Please select the other settings for 4 channels output. Basic 6 Channel Analog Audio Output Mode Use the back audio panel to connect the audio output without any additional module.


MIC at the same time. Click the audio icon “Sound Effect” from the win- dows tray at the bottom of the screen. Please connect the devices to the right jacks as above. A window will appear as right picture if you setup the devices properly. Please note that 3D audio function will only appear when 3D audio inputs.

If you set wrong with the connectors, the warning message will come out as right picture.

Gigabyte GA-8IG1000MK User Manual Page 28

If the device picture shows different from what you set, please press “Manual Selection” to set. How to use the Xpress Recovery a. Excute Backup Utility 2. Excute Restore Utility 3. Remove Backup Image 4. Exit and Restart 1. After install Windows Service Pack, it will show a question mark “? Please remove the question mark and restart the system System will auto-detect the right USB2.

EasyTune 4 Utilities Installation Powerful utility that integrates the overclocking and hardware monitoring functions 1. Click “Finish” to restart computer. Right Click the icon to start “EasyTune 4”. Gigabyte motherboards will auto-detect the external VGA card after it is plugged in, so you don’t need to change any setting manually to disable the onboard VGA.

Why cannot I use the IDE 2? If the cable is your own cable, please remove it from this pin and do not connect any of your own cables to it. Check if the memory install properly into the DIMM slot. Failure has been excluded. Insert the VGA card. Then plug in ATX power cable and turn on the system. If the above procedure unable to solve your problem, please contact with your local retailer or national distributor for help.

Or, you could submit your question to the service mail via Gigabyte website technical support zone http: The appropriate response will be provided ASAP. Page of 96 Go. Install the Central Processing U