DECRETO 2090 HONORARIOS PDF

SCA honorarios del ejercicio de la profesion de arquitectura e ingeniería en colombia. Fiber optic cables can be easily damaged if they are improperly handled or installed. It is imperative that certain procedures be followed in the. Categoría “f”: proyectos de construcción en entiende por construcción en serie la repetición de unidades Iguales para ser cons.

Author: Fegar Nilar
Country: Cuba
Language: English (Spanish)
Genre: Technology
Published (Last): 10 March 2011
Pages: 301
PDF File Size: 4.69 Mb
ePub File Size: 17.33 Mb
ISBN: 804-1-75008-313-4
Downloads: 36538
Price: Free* [*Free Regsitration Required]
Uploader: Vudoshicage

Home Documents Service Epson Post on Oct 35 views. However, should any greatly appreciate being informed of them. The contents of this manual are subject to change without notice. Other product names used herein are for identification purpose only and may be traderespective owners.

EPSON disclaims any and all rights in those marks. When disassembling or assembling a product, be sure to wear gloves to avoid injuries from metal parts with sharp edges. T edures of the printer.

felipe ramirez vasquez – Google+

The instructions and honorario precautions on the preceding page. About This Manualhis manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procrocedures included herein are intended for the experienced repair technicians, and attention should be given to theanual Configurationhis manual consists of six chapters and Appendix.

Indicates an opor condition thaIndicates an opor condition thadamage to, honorarioss dMay indicate anpractice or condefficiently. It marelated to a speachieved througIndicates an opeor condition thator loss hnorarios life. EPHRENo drops to the lower limit, the printer stops printing and n that line again more slowly than before.

Impact Dot MatrixNumber of pins: Black ink ribbonPrint Direction: This mode is not mentioned in users manual. When the power supply voltagethen starts printing remaining o2: When the head temperature risehead temperature falls to the nothan before.

F, paper total thickness is below 5 mm. Front, RearPush tractor feed: Front, Rear Pull tractor feed: Printing on reclaimed paper is avconditions.

Width inch mm 3. Type of paper of multi-part formCarbon-interleaved. Type of paper of line glue at thehorizontal. Type of paper of multi-part forms should be Crbonless. Dont use Carbon-backed and Carbon-interleaved. Type of paper of line glue at the top should be set with the jointing side of paper horizontal. Printing on card is available on2: When setting cards, be sure to aguide.

  GUIDA ALL AEROGRAFO PDF

2090-qr001_-en-p

When Paper size is A6 and decgeto rear entrance only. When using card, set up card mTable MaxWidth inch mm 3. Printing on envelope is honorrios only under normal temperature and humidity conditions2: Set the longer side of envelope horizontally.

When setting envelopes of No. Envelope should be inserted from rear entrance only. Printing is allowed only on the front side; printing on the back side is impossible. Printing on labels is available only under normal temperature and humidity conditions. The base sheet of labels must be continuous paper. Labels should be inserted from bottom or front entrance. Do not pull out paper from backward. No label paper should be left on the printer when the printer is not used.

Service Epson590 2090

Do not print on the base honorarlos of labels. Do not use cut sheet labels. Printing on labels is available o2: The base sheet of labels must b3: Labels should be inserted from 4: Do not pull out paper from back5: No label paper should be left on6: Do not print on the base sheet o7: Roll paper honprarios be set on the roll paper holder option. Roll paper should be inserted from rear entrance only. Release lever position should be friction. UPS Version under the following conditions, the printer enters sleep or statust buffer.

Upon a lapse of 5 minutesmode: This mode realizes noise reduction in exchange of half print speed. Printable Area for Continuous Paperte: The maximum horizontal printable area is Printable Area for Roll PaperTable This signals negative pulse initializes printer.

Connector pin assignment Forward channel Pin No. Input data is latched at falling edge of the dwcreto.

Connector pin aPin No. IEEE nibble mode Adaptable connector: The printer responds to the extensibility request in the affirmative, when the request is 00H or 04H,which 209 Request nibble mode of reverse channel transfer04H: Recommended cable lengt Connector pin assignment and Figure Connector pin assignment Reverse channel n No. In this automatic rinter is initialized to the idle state scanning which r-on. Then the interface that receives data first is ata transfer and the printer is in the stand-by state ied by Default Setting, the printer is returned to the ends data or the printer interface is the busy state, is.

To prevent hosts from this kind of ta very slowly, several bytes per minute, even if the slowdown is started when the rest of the input ds of bytes. At last, when the input buffer is full, ontinuously.

  FINANCE D ENTREPRISE PIERRE VERNIMMEN PDF

These interfaces are selecautomatically.

Colombia: Constitution of with reforms through

Manual selectionOne of the three interfaces can Automatic selectionThe automatic interface selectiinterface selection mode, the pinterface receives data at poweselected. When the host stops dfor the period of seconds specifidle state. As long as the host sthe selected interface is let as it Interface state and interface selWhen the parallel interface is nWhen the Type-B serial interfainterface sends XOFF and sets interface is not selected, the prioptional interface.

Note that thparallel interface is not effectiv Preventing Hosts from Data TrGenerally, hosts abandons databusy state honorqrios dozens of secondtimeout, the printer receives daprinter is in the busy state.

Thisbuffer becomes several thousanthe printer is in the busy state cIEEE Two function modes of IEEE In the case that data is honorariod from printer driver of Windows-based PC, select the packet protocol to “Auto”. Communication is carried out in the convetional mode until a magic decretoo By receiving a magic string, communication in IEEE Honorsrios is carried out in the convetional mode. The packet protocol of IEEE The protocol is not, however, a device control language.

It does provide basic transport-level flow control and multiplexing services. The multiplexed logical channels are independent of each other and blocking of one has no effect on the others. The protocol operates over IEEE Thlocl Mode switches executes the following functions. Normal ModeFunctiones printing and no-printing status.

Micro Adjust function, holding it down for 3 seconds. This setting is for cuctomization purpose only. Pitch LEDswitch is pressedOn, when a locked switch is pushed, the Pause flash simultaneously for three seconds or so.

Paper Out Red The Paper Out LED is on when the printer is in the paper out status, and it blinks when the printer has developed a paper eject error, and it is off when the printer is not in such status. Both LEDs are on when the printer is in default setting mode. ThindTh-Noat decfeto printer refers to at printer initialization.

Print the current setting?? The select sheet will be printed.